My 19 October 2014

Assalamualaikum W.B.T / Annyeonghaseyo.

My second sister just called me at 9.35 am which wake me up from sleeping. She expect me going home this mid semester break, because my young brother and her are coming home for this mid semester break. I told her that I didn't going back to Sabah for this mid semester break. I didn't even open the air asia web page to look up for ticket. I decided to going back at the end of this semester, Insya-Allah.

So, I wake up, went to the living room with my laptop. Here I go again.

This time, was my exactly Catia Assignment. 4 Figures need to draw.

Question 1: Figure T6.5

As I saw straight line and rectangle shape, one word came out on my mind 'OFFSET'!

This will be a lot of offset line.

One of my lecturer commented as he saw my drawing progress,

"Banyaknya line Amal."

and I just smile without looking back. 

I'm just too immersed into this. 

HAhahaha

Step 1.

Let's start with the Sketcher.

I choose black color for the background with grid line. 

Step 2.

→Starting with select the zx plane one the specification tree then click 'Sketcher' icon.

[I'm not familiar with constructing line according to Vertical and Horizontal point s drawing, so actually I start with drawing a rectangle shape and offset those line until I got the intersection line. ]

→Remove all the aid lines so it will be looks like this.

Step 3.

→Got the zx plane view shape, click 'Exit Workbench' icon.

→Click the zx plane (the Sketch.1).

→Click 'Pad' icon until 'Pad Definition' pop up.

→Type: Dimension.

→Length : 42 mm

→Selection : Sketch.1

→Click 'Preview' then 'OK'.

Step 4.

→After pad operation, it will appear like this.
→Don't confuse with the 3 stripe white color, it because I forgot to turn of the lighting effect.
→So, I select the yz pad plane as shown in figure below then click 'Sketcher' icon.

Step 5.

→Entering sketcher, the plane will faced like this.
→By using aids from the offset lines, I drew the rectangle shape [red line].
→Click 'Exit workbench' icon.

Step 6.

→Click the 'Pocket' icon until the 'Pocket Definition' table pop up.
→Type: Dimension
→Depth: 10mm
→Selection: Sketch.2
→Click 'OK'.

Step 7.

→Repeat Step 4, 5, and 6 at the other side.

[Mr. Fendi had thought me how to do the mirror by using a plane, 

but suddenly, I forgot already the actual steps, so I just do it like this. If anyone have a better way to do this, I gladly appreciate it. =) ]

→Select the pad plane as shown below and click 'Sketcher' icon.

Step 8.

→Entering the sketcher, it may faced like this.
→The yellow lines are Offset line just find the middle.
→I drew the circle at the center with diameter of 10 mm.

[Oh ya! I'm not really sure about this, but as shown at the question. It stated that 'Through Hole 20 Diameter. Maybe it should be done by 'Hole' method, but yeah, I not quite sure how it works, so I just used 'Pocket' method.] So, this is how it looks after the pocket operation.

Step 9.

I just want to view this with another option,

so I select the 'Shading with edges and hidden edges' view. 

It's clearly show us the hidden drawing.

Step 10.(Extra but not so important) =D

→ Color: Red and white.

→Lighting: On

→ Just another classy finishing kunun. Ha3. Chill bro.

Xie Xie

Syukran

Arigato Gozaimasu

Kamsahamnida

Terima Kasih

Thank You

 for reading and judging? perhaps? hehehe

Alhamdulillah.

p/s: Have any suggestion? Just drop your comment below. I might consider it with calm and passion. Kunun. hehehe

My 18 October 2014

Alhamdulillah, it's mid semester break.

Yet, it doesn't mean that me as a student may enjoy it like a honeymoon without assignments, tutorials, lab reports, and not to forget the list of mid semester test are waiting a head as soon as the mid semester break is over.

So, I began with my CAD's assignment.

My lecturers gave us 10 pieces of diagrams, 6 of it were our tutorial which should be done during class and another 4 pieces are our assignment.

Alhamdulillah, I had finished drawing 5 of 6 during the class session.

So, this would be the 6th diagram drawing session 

which I proceed at Kolej Kediaman Wang Ulu, Kangar, Perlis.

6th Drawing : Figure T5.12

Step 1.

Open Catia V5R16 

I used Part Design under Mechanical.

Step 2.

→Select the zx plane on the specification tree on the left side.

→Click the sketcher icon.

→ Draw the box with it's  width and height.

→ Oh! I used offset line to the the middle.

→Then, yes offset line again and again to get the intersection point. I just know the advantages of offset this semester. I never familiar with offset when I was learning Autodesk Inventor in my diploma at semester 5 (if I not mistaken) or AutoCAD during at degree semester 1.

→ Got the intersection point, I drew a new line based on it. Then remove all the offset line. So, This is how it's look like.

Step 3.

→After I got the shape on zx plane. 

→Click the icon 'Exit Workbench'.

→Click the 'Pad' icon.

→Select the sketch on zx plane until the 'Pad Definition' pop up.

→The diagram shown thickness in 40 mm, I wrote 40mm in the 'Length:' blank box.

→Likely, I prefer the pad went backward, so I clicked the 'Reverse Direction'.

→Then, click on 'Preview' to see how is it looks like.

Step 4.

→Select the xy plane on the specification tree.

→Draw the box, I used the offset method.

Step 5.

→Click 'Exit workbench'.

→Click 'Pocket' icon (the orange icon as shown below) until the 'Pocket Definition' table pop up.

→Type: Dimension.

→Depth : 18 mm

→Selection: Sketch 4 ( the box)

→Then, click 'Preview' to view the effect of pocket operation.

Step 6.

→This is how it supposed to be done.

→Then, select the pad as shown in the figure below.

Step 7.

→ Select the pad and click 'Sketch' icon.

Step 8.

→On the pad plane, draw a box shape.

→Click 'Exit Workbench' icon.

→ Click 'Pocket' icon, until the 'Pocket Definition' table pop up.

→Type: Dimension.

→Depth : 100 mm

→ Selection : Sketch.5 (the box shape)

→ Click 'Preview' to preview the effect after pocket operation.

→ Then, click 'OK'.

Step 9.

→ Then, tadaaaaa~

→It should be looks like this.

Step 10. (Extra option)

♥As my lecturer shown this function of coloring.

♥So, why not I applied it together in this drawing.

♥It because my lecturer encouraged us to play and used all the function in the CATIA software.

♥So, this feels like playing game.

♥I don't think I was studying or working at all.

♥Maybe, because I know how to do it? and it's quite fun?

♥I don't know or realize how long I spend my time to do only this figure T5.12.

♥Because sometimes, I found its quite confusing and hard to find a way to do the certain part,

but still, keep trying.

♥So, the final appearance of the Figure T5.12 is like this.

(^______^)v

Anyway, there are a lot ways can be used to draw this figure. 

This is the only way that I know how to do it.

It anyone have suggestion to do this better or improve my step in advance.

[Anything comment about grammar also can do. hehehe]

Just drop your comment okay.

I gladly appreciate it. ^____^

Thanks for reading.

P/s: I'm still a beginner and new to CATIA. So, don't ask me about the comparison of CATIA and other product or asking the advanced function of CATIA. Honestly, I don't know. I just spilled out here what I understand during my CATIA class lesson. Oh ya, I'm still weak at tangent though. =D

My 4 October 2014

Di sana sini,

Status para facebookers,

Mesej whatssapian,

Masuk menaik di paparan dinding maya,

Tertera naik menaik seperti tangga di ruang sembang,

Alhamdulillah, 

Setelah 3 minggu lebih,

Tenggelam timbul di sebalik deretan tugasan, laporan, kuliah, dan kuiz,

Mereka selamat sampai di kampung halaman,

Berpeluang meluangkan masa bersama keluarga,

Mungkin lebih meriah dari hari sebelumnya.

Aku yang hanya tahu rasa rindu dan menyayangi,

Setelah berjauhan dengan keluarga dan teman tersayang,

Mungkin cara ini lebih baik buatku,

Kerana rasa rindu dan sayang itu bagai hilang ditiup angin,

Ianya berganti bahagia bila aku bertemu mereka,

Kadang bila bahagia mengaburi mata dan hati,

Rasa penghargaan itu berkurangan,

Dan kurang,

Jauh bezanya bila berjauhan.

Unik bila rasa itu seperti malam dan siang,

silih berganti gelap dan terang,

(tersengih)

Aku di sini,

Hanya suara mereka jadi pengubat hati yang penat,

Hanya gambar mereka jadi jadi lakaran senyuman tawa,

Hanya video lagak mereka jadi hiburan,

Hanya kata-kata mereka jadi simpulan kekuatan,

Aku dan perasaan yang malu untuk diungkapkan dalam kata kpd mereka,

Sayang, Rindu, dan ingat aku di sini.

(senyum sampai nampak gigi kuningku)

My 3 October 2014

Perasaan itu hadir lagi, 

Hadirnya tanpa diduga,

Entah mungkin sekadar singgah bersama angin yg lalu,

Namun risau pula nanti ia bertapa lama,

Tenanglah wahai hati,

Pandang dulu diri ini siapa,

Belum cekap mentadbir dunia sendiri.

"Ya tuhan, kalau dia bukan pendampingku dalam menuju ke destinasiku di dunia ini, hilangkanlah perasaan ini terhadapnya, agar hari-hariku berlalu dgn tenang dan biasa-biasa saja."

Biarpun lama bersua mahupun sekelip mata,

Jika tak diizinkan-NYA utk terdetik di dalam hati,

Tak akan terdetik walau semilimeter,

Kuyakin hatiku dalam genggaman-MU,

Kupercaya jatuh bangunku di dalam perancangan-NYA,

Penat menjaga hati sendiri,

Berikan aku pedoman menyelusuri kehidupan ini.

Bukan disisiku ini.

Mendung awan di langit biru.